Commell LP-173 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Commell LP-173. COMMELL LP-173 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer

Résumé du contenu

Page 1 - Pico-ITX

LP-173 Pico-ITX User’s Manual 2015/06/26 Version:1.56

Page 2 - Packing List:

LP-173 User’s Manual -10- Chapter 2 <Hardware Setup> 2.1 <Connector Location>

Page 3 - (OHSF-173) / (2181010017)

LP-173 User’s Manual -11- 2.2 <Jumper Reference> Jumper Function JRTC CMOS Operating/Clear Setting JAT AT/ATX Mode Setting JVLCD LCD Panel

Page 4

LP-173 User’s Manual -12- 2.4 <Memory Setup> The board provide 204-pin DDR3L SO-DIMM to support 1066/1333MHz up to 8GB. Support Non-ECC, unbuff

Page 5 - 1.1 <Product Overview>

LP-173 User’s Manual -13- 2.6 <SATA Interface> Based on SOC, the board provides one Serial ATAII interfaces with up to 300MB/s of transfer rate

Page 6 - Flexible Extension Interface

LP-173 User’s Manual -14- 5 -CRTATCH 6 IOGND1 7 IOGND1 8 IOGND1 9 NC 10 -CRTATCH 11 NC 12 5VCDA 13 5HSYNC 14 5VSYNC 15 5VCLK 16 NC 2.8.2 <C

Page 7

LP-173 User’s Manual -15- Connector: CN_INV Type: 5-pin Inverter power connector Connector model: molex_53261-5pin or compatible Pin Des

Page 8

LP-173 User’s Manual -16- To setup the LCD, you need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight pow

Page 9 - 1.4 <Block Diagram>

LP-173 User’s Manual -17- If you want to used the LCD panel display when the boot , please go to the BIOS setup. Step1. Configure default BIOS, click

Page 10 - LP-173 User’s Manual

LP-173 User’s Manual -18- Step3. push “F10” to save configuration. Restart your computer. BIOS panel type selection form (BIOS V

Page 11 - 2.2 <Jumper Reference>

LP-173 User’s Manual -19- 2.9 <Onboard Audio Interface> The board provides the onboard high definition audio with Realtek ALC262 Conne

Page 12

LP-173 User’s Manual -2- Copyright Copyright 2012. All rights reserved. This document is copyrighted and all rights are reserved. The information i

Page 13 - 2.7 <LAN Interface>

LP-173 User’s Manual -20- Connector: CN_USB Type: 10-pin (5 x 2) header for USB Port (USB2.0) Pin Description Pin Description 1 VCC 2 VCC 3

Page 14 - 2.8.2 <CN_LVDS>

LP-173 User’s Manual -21- Step3. enable “xHCI Mode” and push “F10” to save configuration. Restart your computer. 1 Step4. If you enable xHCI M

Page 15

LP-173 User’s Manual -22- Step6. Lastly, the “Setup Complete” screen appears so click “Finish” to restart your computer. 2.11 <Serial Port J

Page 16 - LCD Installation Guide:

LP-173 User’s Manual -23- 9 MRI1- 10 N/C 11 MDCD2- 12 MSIN2- 13 MSO2- 14 MDTR2- 15 GND 16 MDSR2- 17 MRTS2- 18 MCTS2- 19 MRI2- 20 N/C 2.12 &l

Page 17

LP-173 User’s Manual -24- 2.12.2 <Power Output> Connector: DC_OUT Type: 6-pin connector for +12V and +5V n Description Pin Description Pin D

Page 18

LP-173 User’s Manual -25- Connector: CPUFAN Type: 3-pin fan wafer connector 2.13 <Indicator and Switch> The JFRNT provides front control pa

Page 19

LP-173 User’s Manual -26- Function Signal PIN Signal Power PWRBT- 1 2 PWRBT+ Speaker SPK- 3 4 SPK+ HDD LED HLED- 5

Page 20

LP-173 User’s Manual -27- Chapter 3 <BIOS Setup> The motherboard uses the Phoenix BIOS for the system configuration. The Phoenix BIOS in the s

Page 21

LP-173 User’s Manual -28- Appendix A <I/O Port Pin Assignment> A.1 <SATA Port> Connector: SATA Type: 10-pin header for SATA Port Pin

Page 22

LP-173 User’s Manual -29- A.3 <LPC Port> Connector: CN_LPC Type: 10-pin header for LPC Port Pin Description Pin Description 1 LPC_CLK 2 RE

Page 23 - 2.12.1 <Power Input>

LP-173 User’s Manual -3- Index Chapter 1 <Introduction> ...

Page 24 - 2.12.3 <Fan Connector>

LP-173 User’s Manual -30- output and TTL-level input. 1. Output:Open-drain, Most applications need use an external pull-up resistor. 2. Input:TTL-lev

Page 25

LP-173 User’s Manual -31- 3. Boot to EFI-Shell mode (UEFI Boot Enable, Legacy Boot Disable) then input the “fs0:” command to switch to the root of

Page 26

LP-173 User’s Manual -32- simple IN/OUT commands. The following lines show an example how to do this. (The GPIO is open drain) GPIO0…..GPIO7 bit0……

Page 27 - Chapter 3 <BIOS Setup>

LP-173 User’s Manual -33- Timeout Value Range - 1 to 255 - Second or Minute Program Sample The integrated Watchdog Timer can be set up by p

Page 28 - A.2 <LAN Port>

LP-173 User’s Manual -34- Contact Information Any advice or comment about our products and service, or anything we can help you please don’t hesitat

Page 29 - A.4 <GPIO Port>

LP-173 User’s Manual -4- 2.3 <Connector Reference>...11 2.3

Page 30 - B.2 Flash Method

LP-173 User’s Manual -5- Appendix D <Programming Watchdog Timer > ... 32 Contact Information...

Page 31

LP-173 User’s Manual -6- Flexible Extension Interface The board provides one PCIe mini slot 1.2 <Product Specification> General Specification

Page 32

LP-173 User’s Manual -7- LP-173E Intel Atom Processor E3845 (2M Cache, 1.91GHz), DVI, LVDS, CRT, Gigabit LAN, USB3.0 & 2.0, Serial Port, SATAII,

Page 33 - Enter configuration

LP-173 User’s Manual -8-

Page 34 - Taiwan Commate Computer Inc

LP-173 User’s Manual -9- 1.4 <Block Diagram>

Commentaires sur ces manuels

Pas de commentaire